Update Assembly Manual

[mjonuschat]

• Use higher contrast text color (Closes Manual text colour hard to read #135)

• Replace "centre" with "center"

• Replace "centred" with "centered"

• Replace "bolt" with "screw"

• Replace "over tighten" with "overtighten"

• Replace "fastening" with "tightening"

• Updated X-Carriage to CW2 (in most places)

• Normalize spelling of "endstop" (Closes Typo on Trident Manual Page 4 #138)

• Normalize various capitalizations of Stealthburner

• Page 2: Replaced colon with double colon, removed comma after "Please" and reordered the first sentence.

• Page 4: Add ASA as recommended material

• Page 4: Link "Print It Forward" to PIF site

• Page 4: Fix "prwint" typo. Add missing "that". (Closes Typo on Trident Manual Page 4 #138)

• Page 5: Added link to forum as help resource

• Page 7: Update the description of "Hammerhead Nut" (Closes Incorrect HAMMERHEAD NUT description #159)

• Page 8: Remove 625 Bearing (Closes Manual page 8 : it shows the 625 bearings while the trident does not have any. #167)

• Page 8: Fix "tickness" and "fastner" typos. Update set screw image.

• Page 9: Added 4mm ball end hex driver

• Page 13: Fix "buildsize" typo

• Page 21: Added missing 90° marker

• Page 33: Fix "thread locker" typo. Change "NEMA17" to "NEMA 17".

• Page 37: Change "NEMA17" to "NEMA 17".

• Page 58: Fix "fastning" typo. Replace rail installation guide image. Use "centered" instead of "centred"

• Page 60: Replace rail installation guide image. Use "centered" instead of "centred".

• Page 61: Rephrased slightly, added missing comma.

• Page 67: Fix double period (Closes Double period in RAIL SAFETY #160)

• Page 68: Replace rail installation guide image. Use "centered" instead of "centred"

• Page 69/73/77: Add whitespace before "mm"

• Page 88-90: Reword the leadscrew lubrication hints

• Page 98: Updated rendering of gantry

• Page 99: Updated drawing of gantry

• Page 100: Add missing heatset inserts for Stealthburner carriage (Closes Manual: X carriage lacks two heat inserts #165)

• Page 111: Replace rail installation guide image. Use "centered" instead of "centred"

• Page 114: Clarification on the missing bolts (Closes [BUGFIX] Use Z_TILT_ADJUST for bed leveling in G32 macro #148)

• Page 131: Centered content

• Page 132: Correct M3x40 -> M3x30 SHCS

• Page 133: Add missing "in", add comma after design

• Page 139: Change "boltheads" to "bolt heads".

• Page 144: Replace "w/out" with "without"

• Page 146: Fix WAGO product number

• Page 147: Add note for bed frame spacing on 300/350mm frame sizes (Closes Manual: 300mm bed frame spacing. #133)

• Page 170: Add hint to rotate deck support clockwise (Closes Suggestion: page 177 - in what direction to rotate #152)

• Page 177: Add hint to rotate zip tie loops clockwise (Closes Suggestion: page 177 - in what direction to rotate #152)

• Page 178: Add hint to rotate zip tie loops clockwise (Closes Suggestion: page 177 - in what direction to rotate #152)

• Page 179: Standardize date format

• Page 191: Fix WAGO product number

• Page 207: Insert PSU image with more detail

• Page 208: Add whitespace before unit

• Page 223: Show correct chain orientation in wiring overview (Closes p223 shows chains pointing both directions #186)

• Page 224: Fix "planing" typo

• Page 227: Fix "ommited" typo

• Page 234: Fix link to additional controller/wiring documentation (Closes Manual: controller board wrong link pg203 #134)

• Page 234: Replace "Hotend" with "Toolhead" in black pill.

• Page 236: Update part cooling fan dimensions to 5015

• Page 261: Add note about the use for the roll-in nuts.

• Page 284: Add note about PTFE tube size and installation procedure (Closes Manual: Explaination PTFE tube from holder to hotend is missing and when to use which tube. #99)

• Page 285: Add note for PTFE tube kind (Closes Manual: Explaination PTFE tube from holder to hotend is missing and when to use which tube. #99)

• Page 286: Replace VORON2 with VORON Trident

• Page 287: Fix "alternativly" typo

• Page 289: Fix "hidding" typo