diff --git a/lib/wled_ADCmanager/library.json b/lib/wled_ADCmanager/library.json
new file mode 100644
index 0000000000..7134127b62
--- /dev/null
+++ b/lib/wled_ADCmanager/library.json
@@ -0,0 +1,5 @@
+{
+  "name": "wled-ADCmanager",
+  "platforms": ["espressif32"],
+  "build": { "libArchive": false }
+}
diff --git a/lib/wled_ADCmanager/wled_ADCmanager.cpp b/lib/wled_ADCmanager/wled_ADCmanager.cpp
new file mode 100644
index 0000000000..b17c045b0e
--- /dev/null
+++ b/lib/wled_ADCmanager/wled_ADCmanager.cpp
@@ -0,0 +1,370 @@
+/*
+ * ADC manager to handle continuous ADC sampling in parallel with single-shot pin reads
+ * by @dedehai (2026) licensed under EUPL 1.2 license
+ *
+ * supports sampling a single pin in continuous ADC mode
+ * calling begin() will start sampling an ADC pin at the given sample rate
+ * if sample rate is higher than the read interval i.e. sampleRateHz/samplesPerFrame, new samples are discarded
+ * if read interval is faster, the read function waits until samples are available or the given timeout elapses
+ * any subsequent call for analogRead() or analogReadMilliVolts() will pause the continuous sampling,
+ * drain the already sampled data into a buffer, read a pin in one-shot mode, then continue the sampling.
+ * replaces analogRead() and analogReadMilliVolts() with managed functions for code compatibility
+
+
+Note: C6 chip revision 0 and 1 have a hardware bug and the effective ADC resolution is only 8bit, was solved in rev. 2 (around mid 2025)
+      https://docs.espressif.com/projects/esp-chip-errata/en/latest/esp32c6/03-errata-description/esp32c6/sar-adc-missing-lower-four-bits.html#sar-adc-loss-of-precision-in-lower-four-bits-of-sar-adc
+
+ TODO:
+ - could add the option to use hardware IIR filter, although the lowest coefficient setting of 2 already has a 3dB cutoff around 2kHz (to be confirmed) at 20kHz sample rate
+ - IIR filter are supported on all modern ESP32 but probably lacking on ESP32 classic, there we would need to do it in post-processing i.e. when writing the sample buffer
+ - need to add a "buffer full" callback? -> is added but no longer needed with the bug being fixed in latest tasmota IDF
+ - there is an edge-case issue: when continuous sampling is running, several analog pins are configured and the pin-info page is open it can lead to crashes (some issue with semaphore) -> cannot reproduce now, might be solved with added semaphore timeout
+ */
+#include "wled.h"
+
+#ifdef ARDUINO_ARCH_ESP32
+#if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0)
+
+// prevent macro recursion of arduino overrides
+#undef analogRead
+#undef analogReadMilliVolts
+
+#define ADCMANAGER_DMA_BLOCKSIZE 128 // DMA buffer block size, IDF driver uses 5 blocks under the hood, there is an ISR call each time a block finishes so dont make it too small
+#define ADCMANAGER_READBUFFERSAMPLES 128 // number of samples to read per chunk from the ADC buffer (stack buffer), do not set higher than 128 or stack overflow may occur
+#define ADCMANAGER_LOCK_TIMEOUT_MS 10 // timeout for mutex lock, this should be as short as possible but still allow for readSamples() to complete before doing analogRead()
+
+#include <string.h>
+
+struct WLEDAdcManager::ContinuousCtx {
+  uint8_t        pin;
+  adc_channel_t  channel;
+  uint32_t       sampleRate;
+  uint16_t       samplesPerFrame;
+  adc_continuous_handle_t handle;
+  int16_t*       cache;
+  uint16_t       cacheSize;
+  uint16_t       cacheCount;
+};
+
+bool WLEDAdcManager::_pinToChannel(uint8_t pin, adc_channel_t* ch) {
+  int8_t c = digitalPinToAnalogChannel(pin);
+  if (c < 0 || c >= SOC_ADC_CHANNEL_NUM(0)) return false; // check if channel is withing ADC1 range (SOC_ADC_CHANNEL_NUM(0) is the number of channels on ADC1)
+  *ch = (adc_channel_t)c;
+  return true;
+}
+
+volatile bool _overflow = false;
+// buffer overflow callback, we need to watch this as prolonged overflow state causes stalls (probably an IDF bug related to DMA ownership)
+static bool IRAM_ATTR _onPoolOvf(adc_continuous_handle_t handle, const adc_continuous_evt_data_t* edata, void* user_data) {
+  _overflow = true;   // set the flag
+  return false;       // nothing to wake
+}
+
+WLEDAdcManager& WLEDAdcManager::instance() {
+  static WLEDAdcManager inst;
+  return inst;
+}
+
+WLEDAdcManager::WLEDAdcManager()
+  : _mutex(nullptr)
+  , _cali(nullptr)
+  , _ctx(nullptr) {
+  _mutex = xSemaphoreCreateMutex();
+}
+
+WLEDAdcManager::~WLEDAdcManager() {
+  end();
+  if (_mutex) vSemaphoreDelete(_mutex);
+#if ADC_CALI_SCHEME_CURVE_FITTING_SUPPORTED
+  if (_cali) adc_cali_delete_scheme_curve_fitting(_cali);
+#endif
+#if ADC_CALI_SCHEME_LINE_FITTING_SUPPORTED
+  if (_cali) adc_cali_delete_scheme_line_fitting(_cali);
+#endif
+}
+
+// initilizes the manager and the hardware and starts sampling
+bool WLEDAdcManager::begin(uint8_t pin, uint32_t sampleRateHz, uint16_t samplesPerFrame) {
+  if (!_mutex || xSemaphoreTake(_mutex, pdMS_TO_TICKS(ADCMANAGER_LOCK_TIMEOUT_MS)) != pdTRUE) return false;
+
+  // tear down any previous session completely
+  if (_ctx) {
+    _endContinuousADC();
+    if (_ctx->cache) { free(_ctx->cache); _ctx->cache = nullptr; }
+    free(_ctx);
+    _ctx = nullptr;
+  }
+
+  adc_channel_t channel;
+  if (!_pinToChannel(pin, &channel)) {
+    xSemaphoreGive(_mutex);
+    return false;
+  }
+
+  _ctx = (ContinuousCtx*)calloc(1, sizeof(ContinuousCtx));
+  if (!_ctx) {
+    xSemaphoreGive(_mutex);
+    return false;
+  }
+
+  _ctx->pin = pin;
+  _ctx->channel = channel;
+  _ctx->sampleRate = sampleRateHz;
+  _ctx->samplesPerFrame = samplesPerFrame;
+  _ctx->cacheSize = samplesPerFrame;
+  _ctx->cacheCount = 0;
+  _ctx->cache = (int16_t*)calloc(_ctx->cacheSize, sizeof(int16_t));
+  if (!_ctx->cache) {
+    free(_ctx);
+    _ctx = nullptr;
+    xSemaphoreGive(_mutex);
+    return false;
+  }
+
+  bool ok = _initContinuousADC();
+  if (!ok) {
+    free(_ctx->cache);
+    free(_ctx);
+    _ctx = nullptr;
+  }
+  xSemaphoreGive(_mutex);
+  return ok;
+}
+
+// stop sampling and deinitialize the AdcManager continuous mode (use this if you want to sample a different pin or do not need to sample anymore)
+void WLEDAdcManager::end() {
+  if (!_mutex || xSemaphoreTake(_mutex, pdMS_TO_TICKS(ADCMANAGER_LOCK_TIMEOUT_MS)) != pdTRUE) return;
+  if (_ctx) {
+    _endContinuousADC();
+    if (_ctx->cache) { free(_ctx->cache); _ctx->cache = nullptr; }
+    free(_ctx);
+    _ctx = nullptr;
+  }
+  xSemaphoreGive(_mutex);
+}
+
+// initialize the hardware
+bool WLEDAdcManager::_initContinuousADC() {
+  if (!_ctx) return false;       // begin() not called
+  if (_ctx->handle) return true; // already initialized
+  size_t frameBytes = (size_t)_ctx->samplesPerFrame * sizeof(adc_digi_output_data_t);
+  adc_continuous_handle_cfg_t hcfg = {
+    .max_store_buf_size = frameBytes + frameBytes/2, // hold one and a half frames in buffer, caller needs to drain it fast enough to avoid data loss (can increase to avoid data loss but still need to drain fast enough at one point)
+    .conv_frame_size    = ADCMANAGER_DMA_BLOCKSIZE, // use fixed DMA buffer size of 256 bytes (ADC driver creates 5 DMA descriptors with one buffer each, at 20kHz this means an interrupt every 1.4ms
+    .flags = { .flush_pool = false }, // do not flush the store buffer on overrun but discard new samples (true means discard oldest, is much slower and can cause issues, do not set true)
+  };
+  if (adc_continuous_new_handle(&hcfg, &_ctx->handle) != ESP_OK) return false;
+
+  // register the overflow callback to catch buffer overflows before they case a stall
+  adc_continuous_evt_cbs_t cbs = { .on_conv_done = nullptr, .on_pool_ovf = _onPoolOvf };
+  adc_continuous_register_event_callbacks(_ctx->handle, &cbs, this);
+
+
+  adc_digi_pattern_config_t pat = {
+    .atten     = ADC_ATTEN_DB_12,
+    .channel   = (uint8_t)_ctx->channel,
+    .unit      = ADC_UNIT_1,
+    .bit_width = ADC_BITWIDTH_12,
+  };
+  adc_continuous_config_t cfg = {
+    .pattern_num    = 1,
+    .adc_pattern    = &pat,
+    .sample_freq_hz = _ctx->sampleRate,
+    .conv_mode      = ADC_CONV_SINGLE_UNIT_1,
+    .format         = WLED_ADC_DIGI_FORMAT,
+  };
+  // initialize and start sampling
+  if (adc_continuous_config(_ctx->handle, &cfg) != ESP_OK || adc_continuous_start(_ctx->handle) != ESP_OK) {
+    _endContinuousADC();
+    return false;
+  }
+  return true;
+}
+
+// stop sampling and de-initilize the hardware so it can be used by analogRead() but keeps the continuous _ctx configuration
+void WLEDAdcManager::_endContinuousADC() {
+  if (!_ctx) return;
+  if (_ctx->handle) {
+    adc_continuous_stop(_ctx->handle);
+    adc_continuous_deinit(_ctx->handle);
+    _ctx->handle = nullptr;
+  }
+}
+
+void WLEDAdcManager::_drainToCache() {
+  if (!_ctx || !_ctx->handle || !_ctx->cache) return; // safety check
+  adc_digi_output_data_t temp[32]; // size of data packets to request, 32 samples at 22kHz is 1.5ms, leftover samples are lost
+  while (_ctx->cacheCount < _ctx->cacheSize) {
+    uint32_t n = 0;
+    // read what is available in the buffer in chunks (no timeout means do not wait for any additional samples)
+    if (adc_continuous_read(_ctx->handle, (uint8_t*)temp, sizeof(temp), &n, 0) != ESP_OK || n == 0) break;
+    uint16_t cnt = n / sizeof(adc_digi_output_data_t);
+    for (uint16_t i = 0; i < cnt && _ctx->cacheCount < _ctx->cacheSize; i++) {
+      _ctx->cache[_ctx->cacheCount++] = (int16_t)(temp[i].WLED_ADC_OUT_TYPE.data);
+    }
+  }
+}
+
+// read samples acquired in continuous mode. They are written as 12bit unsigned values into the passed buffer
+// tries to read "numSamples" and returns the actual number of samples written into the buffer
+// it waits up to timeoutMs total while fetching tmpBfrSize (128) samples at a time, if not enough samples are available, it returns what it got
+// to poll the buffer and "just give me what you got" use a timeout of 0. On read error, it restarts the driver so no action needed by caller.
+// note: maximum timeout is ADCMANAGER_LOCK_TIMEOUT_MS-1, so make sure to call this function in reasonable intervals if you need all samples (or increase the lock time)
+uint16_t WLEDAdcManager::readSamples(int16_t* buffer, uint16_t numSamples, uint32_t timeoutMs) {
+  if (!buffer || !numSamples) return 0;
+  // note: DMA uses SOC_ADC_DIGI_MAX_BITWIDTH which is 12bits on all checked units TODO: should make sure and handle this to future proof it
+  if (!_mutex || xSemaphoreTake(_mutex, pdMS_TO_TICKS(ADCMANAGER_LOCK_TIMEOUT_MS)) != pdTRUE) return 0;
+  // check if continuous mode is running AFTER we take the semaphore, otherwise we could have a race with analogRead()
+  if (!_ctx || !_ctx->handle) {
+    xSemaphoreGive(_mutex);
+    return 0;
+  }
+
+  const uint32_t maxReadTimeoutMs = ADCMANAGER_LOCK_TIMEOUT_MS - 1;
+  const uint32_t readTimeoutMs = timeoutMs < maxReadTimeoutMs ? timeoutMs : maxReadTimeoutMs;
+  const uint32_t readStartMs = millis();
+  uint16_t out = 0; // number of samples written to the buffer
+  // check if any data was cached during an intermediate analogRead()
+  if (_ctx->cacheCount) {
+    uint16_t copy = _ctx->cacheCount < numSamples ? _ctx->cacheCount : numSamples;
+    memcpy(buffer, _ctx->cache, copy * sizeof(int16_t));
+    out = copy;
+    if (copy < _ctx->cacheCount) {
+      memmove(_ctx->cache, _ctx->cache + copy, (_ctx->cacheCount - copy) * sizeof(int16_t));
+    }
+    _ctx->cacheCount -= copy;
+  }
+
+  if (out >= numSamples) {
+    xSemaphoreGive(_mutex);
+    return out; // already get enough samples from cache
+  }
+
+  const int tmpBfrSize = ADCMANAGER_READBUFFERSAMPLES; // use fixed size buffer on stack to read samples from the driver in chunks
+  adc_digi_output_data_t temp[tmpBfrSize];
+
+  while (out < numSamples) {
+    const uint32_t elapsedMs = millis() - readStartMs;
+    if (elapsedMs >= readTimeoutMs) break;
+
+    uint32_t n = 0;
+    uint16_t want = (numSamples - out) < tmpBfrSize ? (numSamples - out) : tmpBfrSize;
+    size_t wantBytes = want * sizeof(adc_digi_output_data_t);
+    uint32_t remainingMs = readTimeoutMs - elapsedMs;
+    esp_err_t err = adc_continuous_read(_ctx->handle, (uint8_t*)temp, wantBytes, &n, remainingMs);
+
+    // copy the data into 16bit buffer
+    if (n > 0) {
+      uint16_t got = n / sizeof(adc_digi_output_data_t);
+      for (uint16_t i = 0; i < got; i++) {
+        buffer[out++] = (int16_t)(temp[i].WLED_ADC_OUT_TYPE.data);
+      }
+    }
+
+    if (err == ESP_ERR_TIMEOUT && n > 0) {
+      break; // not enough samples within timeout frame, return what we got
+    }
+    if (err != ESP_OK) {
+      DEBUG_PRINTF_P(PSTR("ADC read error %d, got n=%d restarting"), err, n);
+      _endContinuousADC();
+      _initContinuousADC();
+      break;
+    }
+    else if (n == 0) break; // should not happen, just in case (if no samples are read, it should not be ESP_OK)
+  }
+
+  if (_overflow) {
+    // stop-flush-restart: this is a dirty workaround for a bug in the IDF driver that can cause de-sync and permanent firing of interrupts,
+    // stalling everything. stop-start takes about 0.3ms and resets the DMA so everything keeps working.
+    DEBUG_PRINTF_P(PSTR("ADC buffer overflow"));
+    _overflow = false;
+    adc_continuous_stop(_ctx->handle);
+    adc_continuous_flush_pool(_ctx->handle); // flush remaining data and make sure pool does not overflow
+    adc_continuous_start(_ctx->handle);
+  }
+
+  xSemaphoreGive(_mutex);
+  return out;
+}
+
+// a one-shot read takes about 0.7-2.5ms if continuous reading is active, depending on chip type (ESP32 is slower, newer ones are faster), 0.2ms otherwise
+bool WLEDAdcManager::_oneshotRead(adc_channel_t ch, int* outRaw) {
+  adc_oneshot_unit_handle_t h;
+  adc_oneshot_unit_init_cfg_t icfg = {
+    .unit_id = ADC_UNIT_1,
+    .ulp_mode = ADC_ULP_MODE_DISABLE };
+  if (adc_oneshot_new_unit(&icfg, &h) != ESP_OK) return false;
+
+  adc_oneshot_chan_cfg_t ccfg = {
+    .atten = ADC_ATTEN_DB_12,
+    .bitwidth = ADC_BITWIDTH_12 };
+  adc_oneshot_config_channel(h, ch, &ccfg);
+
+  bool ok = (adc_oneshot_read(h, ch, outRaw) == ESP_OK);
+  adc_oneshot_del_unit(h);
+  if (ok) {
+    // The raw result is in SOC_ADC_RTC_MAX_BITWIDTH bits, independent of .bitwidth set above, we use 12bit in WLED
+    #if (SOC_ADC_RTC_MAX_BITWIDTH > 12)
+      *outRaw >>= (SOC_ADC_RTC_MAX_BITWIDTH - 12);
+    #elif (SOC_ADC_RTC_MAX_BITWIDTH < 12)
+      *outRaw <<= (12 - SOC_ADC_RTC_MAX_BITWIDTH);
+    #endif
+  }
+  return ok;
+}
+
+int WLEDAdcManager::analogRead(uint8_t pin) {
+  int raw = 0;
+  adc_channel_t ch;
+  if (!_pinToChannel(pin, &ch)) return 0;
+
+  if (!_mutex || xSemaphoreTake(_mutex, pdMS_TO_TICKS(ADCMANAGER_LOCK_TIMEOUT_MS)) != pdTRUE) return 0;
+  if (_ctx) { // continuous sampling is used
+    _drainToCache();
+    _endContinuousADC();  // stop sampling and free the ADC hardware if in use
+    _oneshotRead(ch, &raw);
+    _initContinuousADC(); // re-init and start sampling again
+  } else {
+    _oneshotRead(ch, &raw);
+  }
+  xSemaphoreGive(_mutex);
+  return raw;
+}
+
+bool WLEDAdcManager::_initCali() {
+  if (_cali) return true;
+
+#if ADC_CALI_SCHEME_CURVE_FITTING_SUPPORTED
+  adc_cali_curve_fitting_config_t cfg = {
+    .unit_id  = ADC_UNIT_1,
+    #if SOC_ADC_CALIB_CHAN_COMPENS_SUPPORTED
+    //.chan     = adc_channel_t(channel); // per channel calibration is not implemented (C5, C6, P4 support it). trading complexity for a few mV of inaccuracy here.
+    #endif
+    .atten    = ADC_ATTEN_DB_12,
+    .bitwidth = ADC_BITWIDTH_12,
+  };
+  if (adc_cali_create_scheme_curve_fitting(&cfg, &_cali) == ESP_OK) return true;
+#endif
+
+#if ADC_CALI_SCHEME_LINE_FITTING_SUPPORTED
+  adc_cali_line_fitting_config_t cfg = {
+    .unit_id  = ADC_UNIT_1,
+    .atten    = ADC_ATTEN_DB_12,
+    .bitwidth = ADC_BITWIDTH_12,
+  };
+  if (adc_cali_create_scheme_line_fitting(&cfg, &_cali) == ESP_OK) return true;
+#endif
+  return false;
+}
+
+#if SOC_ADC_DIG_IIR_FILTER_SUPPORTED
+#endif
+
+int WLEDAdcManager::analogReadMilliVolts(uint8_t pin) {
+  int raw = analogRead(pin); // returns 0 on an invalid pin or error
+  int mv = 0;
+  if ((_cali || _initCali()) && adc_cali_raw_to_voltage(_cali, raw, &mv) == ESP_OK) return mv;
+  return (raw * 3300) / 4095; // fallback to linear conversion if calibration fails
+}
+#endif // ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0)
+#endif // ARDUINO_ARCH_ESP32
diff --git a/lib/wled_ADCmanager/wled_ADCmanager.h b/lib/wled_ADCmanager/wled_ADCmanager.h
new file mode 100644
index 0000000000..8d56ad63c7
--- /dev/null
+++ b/lib/wled_ADCmanager/wled_ADCmanager.h
@@ -0,0 +1,70 @@
+/*
+ * ADC manager to handle continuous ADC sampling in parallel with single-shot pin reads
+ * by @dedehai (2026) licensed under EUPL 1.2 license
+ */
+
+#pragma once
+
+#ifdef ARDUINO_ARCH_ESP32
+#if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0)
+
+#include <stdint.h>
+#include <Arduino.h>
+#include <driver/gpio.h>
+#include <esp_adc/adc_continuous.h>
+#include <esp_adc/adc_oneshot.h>
+#include <esp_adc/adc_cali.h>
+#include <freertos/FreeRTOS.h>
+#include <freertos/semphr.h>
+
+#if defined(CONFIG_IDF_TARGET_ESP32) || defined(CONFIG_IDF_TARGET_ESP32S2)
+  #define WLED_ADC_DIGI_FORMAT ADC_DIGI_OUTPUT_FORMAT_TYPE1
+  #define WLED_ADC_OUT_TYPE    type1
+#else
+  #define WLED_ADC_DIGI_FORMAT ADC_DIGI_OUTPUT_FORMAT_TYPE2
+  #define WLED_ADC_OUT_TYPE    type2
+#endif
+
+class WLEDAdcManager {
+public:
+  static WLEDAdcManager& instance();
+
+  bool begin(uint8_t pin, uint32_t sampleRateHz, uint16_t samplesPerFrame);
+  void end();
+  bool isRunning() const { return _ctx != nullptr; }
+
+  uint16_t readSamples(int16_t* buffer, uint16_t numSamples, uint32_t timeoutMs = 100);
+
+  int analogRead(uint8_t pin);
+  int analogReadMilliVolts(uint8_t pin);
+
+private:
+  WLEDAdcManager();
+  ~WLEDAdcManager();
+  WLEDAdcManager(const WLEDAdcManager&) = delete;
+  WLEDAdcManager& operator=(const WLEDAdcManager&) = delete;
+
+  static bool _pinToChannel(uint8_t pin, adc_channel_t* ch);
+
+  bool _initContinuousADC();
+  void _endContinuousADC();
+  void _drainToCache();
+  bool _oneshotRead(adc_channel_t ch, int* outRaw);
+  bool _initCali();
+
+  struct ContinuousCtx;          // forward declaration
+  SemaphoreHandle_t _mutex;
+  adc_cali_handle_t _cali;
+  ContinuousCtx*    _ctx;        // nullptr when continuous mode is idle
+};
+
+// override of native Arduino functions for compatibility with external usermods
+
+#undef analogRead
+#define analogRead(pin) WLEDAdcManager::instance().analogRead(pin)
+#undef analogReadMilliVolts
+#define analogReadMilliVolts(pin) WLEDAdcManager::instance().analogReadMilliVolts(pin)
+// ESP8266: do not override analogRead
+// we could add analogReadMilliVolts() which would just return (int)(analogRead(pin) / 1023.0f);
+#endif // ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0)
+#endif // ARDUINO_ARCH_ESP32
diff --git a/platformio.ini b/platformio.ini
index 8a060ba0fe..ffeb51b354 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -224,7 +224,6 @@ lib_deps =
   https://github.com/tignioj/ArduinoUZlib.git#20aff95cd80c141f80bdbf66895409a0046d2c2f
   ${env.lib_deps}
   https://github.com/Makuna/NeoPixelBus.git#1d7ff38f14d04a976f9c6e365c83a232bcba04fc ;; standard NPB version used in main branch
-
 monitor_filters = esp8266_exception_decoder
 
 ;; compatibilty flags - same as 0.14.0 which seems to work better on some 8266 boards. Not using PIO_FRAMEWORK_ARDUINO_MMU_CACHE16_IRAM48
@@ -316,7 +315,8 @@ lib_deps =
   https://github.com/someweisguy/esp_dmx.git#47db25d8c515e76fabcf5fc5ab0b786f98eeade0
   ${env.lib_deps}
   NeoPixelBus = git+https://github.com/Makuna/NeoPixelBus#1d7ff38f14d04a976f9c6e365c83a232bcba04f ;; latest release + properly inialized buffers
-lib_ignore = 
+lib_ignore =
+  wled-ADCmanager ; ADCmanager is only available on IDF V5.5
 
 [esp32_idf_V5]
 ;; build environment for ESP32 using ESP-IDF 5.3.4 / arduino-esp32 v3.1.10
diff --git a/wled00/wled.h b/wled00/wled.h
index 9bafb49196..aec3876902 100644
--- a/wled00/wled.h
+++ b/wled00/wled.h
@@ -115,6 +115,9 @@
     #include <LittleFS.h>
   #endif
   #include "esp_task_wdt.h"
+  #if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0)
+  #include <wled_ADCmanager.h>
+  #endif
 #endif
 #include <Wire.h>
 #include <SPI.h>